+86 13816508465
Pump Introductions
Aug. 25, 2026
The Stream SXR is a three-speed circulation pump designed for reliable water circulation in heating, air conditioning, domestic hot water, and solar water heating systems. Combining three selectable operating speeds with wet-runner technology, dry-running protection, corrosion-resistant hydraulic components, and a wide fluid temperature range from -10°C to +110°C, the SXR provides a practical circulation solution for residential and commercial water systems.
Efficient water circulation is essential to the performance of hydronic heating and hot water systems. Without sufficient circulation, heat may not be distributed evenly through radiators or underfloor heating loops, hot water may take longer to reach fixtures, and boilers or other heat sources may operate less effectively.
At the same time, using more pump capacity than a system actually requires can create unnecessary flow, noise, and energy consumption. Different installations also have different hydraulic requirements depending on pipe length, system resistance, building size, and the number of heating or cooling circuits.
The Stream SXR Three-Speed Circulation Pump addresses these requirements with multi-speed operation. Users and installers can select an operating speed according to the hydraulic requirements of the system, providing a simple way to adapt pump performance without the complexity of a fully electronic variable-speed circulator.
The Stream SXR is a fixed-speed circulator with three selectable speed settings. It is designed to continuously move water through closed or recirculating piping systems rather than transfer water from one independent location to another.
This makes it fundamentally different from a conventional surface water pump. A circulation pump is typically installed directly within a piping loop and maintains water movement between the heat source, distribution network, and terminal equipment.
The SXR series is designed for water circulation in heating, air conditioning, and domestic hot water systems. Its range of specifications allows different SXR models to be matched to different system requirements.
Typical applications include boiler and hydronic heating systems, general heating systems, cooling systems, domestic hot water recirculation, and solar water heating systems.
One of the defining features of the Stream SXR is its three-speed operation.
Hydronic systems do not all require the same flow rate or pump head. A small domestic heating circuit may have relatively low hydraulic resistance, while a larger system with longer pipework, multiple radiators, or several heating zones may require greater circulation performance.
The SXR allows the operating speed to be selected according to system requirements rather than forcing the pump to operate at only one fixed performance level.
A lower speed may be suitable when hydraulic demand is limited, while a higher speed can provide additional circulation when greater flow or head is required.
This three-speed approach gives installers a straightforward way to adapt pump operation during commissioning and system balancing.
Noise is an important consideration for circulation pumps because they are frequently installed inside residential buildings and may operate for extended periods.
The Stream SXR uses high-quality wet-runner technology designed for low-noise operation.
In a wet-runner circulator, the pumped liquid plays an important role within the rotor assembly. This design eliminates the need for the conventional external motor cooling arrangement found on many surface pumps and helps provide smooth, quiet operation.
Low operating noise is particularly valuable in residential heating systems, where circulation equipment may be installed near bedrooms, living spaces, utility rooms, or other occupied areas.
Water is essential to the normal operation of a wet-runner circulation pump. Operating without sufficient water can cause excessive heat and damage internal pump components.
The Stream SXR incorporates dry-running protection designed to protect the pump against dry-running during startup and normal operation.
This provides an additional layer of protection during abnormal system conditions and can help reduce the risk of pump damage caused by insufficient water inside the circulation circuit.
Correct filling, venting, installation, and commissioning of the system remain essential even when dry-running protection is available.
Mineral deposits and scale can affect water circulation equipment over time, particularly in heating and domestic hot water applications.
The SXR is designed to be easy to clean and lime-resistant, helping simplify maintenance and support reliable operation over the life of the system.
This feature can be particularly useful in regions with harder water, where mineral deposits may accumulate more quickly inside water-handling equipment.
Circulation pumps operate in continuous contact with the circulating medium, making corrosion resistance an important consideration for hydraulic components.
The Stream SXR uses a corrosion-resistant impeller and pump housing to improve durability in suitable circulation applications.
Different impeller and pump body configurations can also be customized according to the specific SXR model and application requirements.
Installation time is an important consideration for heating contractors, plumbers, and system integrators.
The SXR is designed for quick and simple electrical installation, helping streamline pump replacement and new system installation.
Its compact circulator configuration also makes it suitable for installation directly into circulation pipework where space may be limited.
The SXR supports a broad fluid temperature range from -10°C to +110°C.
This wide operating range allows the pump to serve both heating and cooling applications rather than being restricted to conventional hot water circulation alone.
At the upper end of the range, the SXR is suitable for high-temperature water circulation within its rated conditions. At lower temperatures, it can also support suitable cooling system applications.
This versatility makes the SXR relevant to HVAC contractors and distributors serving multiple circulation applications with one pump family.
Boiler and hydronic heating systems are among the primary applications for the SXR.
In a hydronic system, the boiler heats water and the circulation pump moves that heated water through pipes to radiators, convectors, underfloor heating circuits, or other heat emitters.
Without adequate circulation, heat distribution can become uneven and some parts of the building may take longer to reach the desired temperature.
The SXR's three-speed adjustment allows installers to select a circulation level according to the hydraulic resistance and flow requirements of the heating circuit.
Water-based underfloor heating systems depend on continuous and controlled circulation through long loops of pipe installed beneath the floor.
The circulation pump must provide enough flow to distribute heated water through these loops while overcoming the hydraulic resistance created by the pipework, manifolds, valves, and fittings.
A three-speed circulation pump can be useful in these installations because the operating level can be adjusted during system commissioning and balancing.
The SXR's low-noise wet-runner design is also well suited to residential underfloor heating applications where quiet operation is desirable.
In larger homes and buildings, the distance between the water heater and the furthest faucet or shower can result in long waiting times for hot water.
A domestic hot water recirculation system maintains circulation through a dedicated piping loop so that hot water remains available closer to the points of use.
The SXR can provide the circulation required for suitable domestic hot water recirculation systems, helping improve user convenience and reduce the delay before hot water reaches fixtures.
The SXR can be integrated into a variety of heating systems where water or another compatible liquid must circulate between the heat source and the distribution network.
The selectable speed settings provide flexibility when matching pump performance to different system layouts and hydraulic requirements.
Circulation pumps are not limited to heating applications.
The SXR can also be used in suitable cooling systems where fluid circulation is required to transfer thermal energy through the system.
Its fluid temperature rating down to -10°C expands the potential operating range for appropriate cooling applications.
Parameter
Specification
Series | Stream SXR |
Pump Type | Three-Speed Fixed-Speed Circulation Pump |
Operating Speeds | 3 Selectable Speeds |
Fluid Temperature Range | -10°C to +110°C |
Maximum Permissible Ambient Temperature | 40°C |
Degree of Protection | IP44 |
Insulation Class | Class H |
Power Supply | 1~230V, 50Hz |
Motor Technology | Wet-Runner |
Dry-Running Protection | Yes |
Flow, head, impeller material, pump body material, and other specifications vary according to the individual SXR model and configuration. The specific model should therefore be selected according to the hydraulic requirements of the installation.
A single-speed circulation pump operates at one fixed performance level. This can be sufficient when the system has predictable and fixed hydraulic requirements, but it provides limited flexibility during installation and commissioning.
A three-speed circulation pump gives installers three operating levels to better match pump performance to the system.
For example, if the highest speed produces more circulation than necessary, the pump can be switched to a lower setting. If the system requires additional flow to overcome greater hydraulic resistance, a higher speed can be selected.
This provides a simple balance between conventional fixed-speed pump construction and more advanced electronically controlled variable-speed circulation pumps.
Single-Speed Circulation Pump
Stream SXR Three-Speed Pump
One fixed operating speed | Three selectable operating speeds |
Limited adjustment after installation | Performance can be adjusted to system requirements |
May provide more or less circulation than required | Three settings provide greater matching flexibility |
Suitable for simple fixed-demand systems | Suitable for a broader range of heating and circulation systems |
Three-speed and electronically controlled variable-speed circulation pumps serve different market requirements.
The SXR provides three manually selectable operating speeds, giving installers straightforward control over pump performance while maintaining a simple and economical pump design.
A high-efficiency variable-speed circulator uses electronic control and a variable-speed motor to adjust operation across a wider range. Depending on the model, these pumps may include automatic adaptation, proportional pressure, constant pressure, PWM, or other advanced operating modes.
For projects where simple installation, proven technology, and straightforward three-level adjustment are priorities, the SXR provides a practical solution. Where automatic hydraulic adaptation and higher energy-efficiency requirements are the main priority, an electronically controlled high-efficiency circulator may be more appropriate.
Selecting a circulation pump should be based primarily on the required flow rate and head of the system.
Required flow depends on the amount of heat that must be transported through the system and the designed temperature difference between supply and return water.
Required pump head is determined primarily by hydraulic resistance. Pipe length, pipe diameter, manifolds, valves, fittings, heat exchangers, radiators, and underfloor heating loops all contribute to pressure loss.
The physical height of a closed hydronic heating system should not be treated in the same way as the static lifting height of an open water transfer system. In a properly filled closed circulation loop, pump sizing is primarily concerned with overcoming system resistance and maintaining the required circulation flow.
Once the appropriate SXR model has been selected, the three-speed function provides an additional adjustment option during system commissioning.
The objective is not automatically to operate the pump at the highest speed. The appropriate setting is the one that provides sufficient circulation for the system without unnecessary flow.
The Stream SXR is designed for boiler and hydronic heating systems, general heating systems, cooling systems, domestic hot water recirculation, and solar water heating systems.
The SXR provides three selectable operating speeds, allowing pump operation to be adapted to different system requirements.
The SXR can be used in suitable hydronic heating applications, including water-based underfloor heating systems, when the selected model provides the flow and head required by the installation.
Yes. Domestic hot water recirculation is one of the specified applications for the SXR series. The appropriate pump body and impeller configuration should be selected for the intended system.
The SXR is rated for circulating fluids at temperatures up to +110°C.
The specified fluid temperature range extends down to -10°C, allowing the SXR to serve suitable heating and cooling circulation applications.
The SXR uses high-quality wet-runner technology designed for low-noise operation, making it suitable for residential heating and hot water circulation applications.
Yes. The SXR incorporates dry-running protection for startup and normal operating conditions.
The Stream SXR has an IP44 degree of protection.
The SXR is specified with Class H insulation.
The specified main power supply is single-phase 230V at 50Hz.
Yes. Solar water heating is one of the intended applications listed for the SXR series.
The SXR is a three-speed circulation pump rather than a continuously variable electronic circulator. Users can select between three operating speeds according to system requirements.
The Stream SXR Three-Speed Circulation Pump provides a straightforward and reliable solution for circulating water in heating, cooling, domestic hot water, and solar water heating systems.
Its three selectable speeds allow installers to adapt pump operation to different hydraulic requirements, while wet-runner technology supports quiet operation in residential and commercial environments.
With dry-running protection, lime-resistant design, corrosion-resistant hydraulic components, Class H insulation, IP44 protection, and a wide fluid temperature range from -10°C to +110°C, the SXR is designed for dependable operation across a broad range of circulation applications.
For distributors, HVAC contractors, plumbers, and heating system installers looking for a practical three-speed circulator for boilers, hydronic heating, domestic hot water recirculation, cooling, or solar heating systems, the Stream SXR offers a flexible combination of simple speed adjustment, low-noise operation, and broad application compatibility.
```
Address
No.17 XeDa Jimei Ind. Park, Xiqing Economic Development Area, Tianjin, China
Telephone
+86 13816508465
QUICK LINKS
